Connect and share knowledge within a single location that is structured and easy to search. In my rebuilding project I have counted 18 outlets and lights on one bedroom circuit that travels through 3 rooms.
Is that ok? Also, check your breaker. For example, don't expect to run an electric chainsaw and a vacuum at the same time off a single 15A circuit. If you have a 15A breaker attached which is likely the case, I would recommend not running any major appliances Such as a Microwave or Window AC unit off of it, since that will take up most of your juice, and one too many lamps in the other 17 outlets could trip your breaker.
If you need to run a heavy appliance, just wire in another circuit, and don't drill a hole through the wires near the breaker box Voice of experience. Depends where you are and for what value of OK you are looking. So long as the breaker is 15 amps it should be "safe. Other people have mentioned some inspectors in the US having an expectation of "around 7" but I don't think code was ever found to support that, other than the code of "do what it takes to get the inspector off your back.
Personally, I'd break it up, and separate lighting from outlets I detest being left in the dark when something plugged into an outlet causes a trip. However, if the bulk of what is happening at the outlets is "nothing" or "wall-wart for a phone" or basically if you don't trip it much, you COULD leave it alone. It's certainly going to be cheaper to do nothing. Without knowing how many devices were lights.
But I have a particular philosophy, and there's no code requirement to do it my way. There are some assumptions that were missed in this discussion, so I will point out the missing questions by listing them here.
It looks like there was too few funds or not enough talent to actually design a SAFE and good working electrical system in your home. I was actually searching for a nice schematic for a 4 way switch to 19 LED recessed ceiling lights so I could share that with a co worker who is just starting out and is eager to learn. GFCI not installed correctly or not at all in the "best locations" Yes, its creative Yes, it is sexy looking so tight I AM an avionics tech Breakers are there for when a peice of equipment is faulty or someone violates the assumptions that went into the installation.
They are not there to limit load in normal use. This means you need to think about what loads are likely to be used where. Especially if you live in a place with relatively low power socket circuits from the terminology you use i'm guessing you are in america.
From a compliance perspective it's going to depend on where you live. Others leave it to the judgement of the installer. That's not dangerous, or illegal code-wise possibly , and it is ok to have that. But I must say, in all of the units I service, I havn't seen that many outlets on one circuit. Turn all those on at once and BAM You are over and the breaker will trip. And any counter that is more than two feet long needs an outlet. And all countertop outlets must be GFCI protected.
But hey each to their own right. My rule of thumb and code is. An outlet within six feet in either direction of the bedroom door and within 10 feet from there all around the room. So plan carefully when you get to the closets. And when we lost power during Hurricane Sandy we had all the lights in the house working on a generator.
Ex- 12 plugs on 1 15 amp breaker. Same as Rick how to install a transfer switch, when the sevice lines are live, can it be done without calling elec. Whole house transfer, not just individule circuits.
Also, you should know modern-day U. So, if you are using a 15 amp circuit and you are using regular volt outlets, then the max watts you can use is watts. All electrical appliances like TVs, chargers, and lightbulbs should state their wattage on the packaging so you can just add up the expected wattage from each appliance to get your total wattage for the circuit.
Most new construction bedrooms have an outlet every 6 feet, or on every wall. They would also have a junction box on the ceiling for a light and fan. For example, a master bedroom could have 7 outlets, and then a light fixture at the ceiling for a fan. All while, being on a 15 amp circuit. While there is no direct rule for how many outlets you can have on a 15 amp circuit, you should not have more than watts of power plugged into those outlets at one time.
Again, a good rule of thumb is 1. In the case of 15 amps, we recommend a maximum of 8 outlets. During our home inspections , while we do not count the specific number of outlets in any given room, we will ensure the amperage per room is appropriate. For example, a kitchen should have more than a 15amp breaker. Learn about preventing power surges or how many outlets can you put on a 20 amp circuit. Hello, I want to install 7 volts elect plugs in my basement.
0コメント